Reasons Your fiat ducato key replacement 500 key (click to investigate) Fob Won't Work

A fiat doblo key programming 500 key fob is a convenient method to open the doors and begin the car. There are a myriad of reasons the fob could stop working. These include a dead coin battery, damaged receiver module, water damage problems, and interference.

This listing is for an NEW replacement fiat car key cutting Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not functioning. Modern key fobs operate with a restricted operating range, and should be within only a few feet from the vehicle to operate. If you're far from your vehicle and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a new one of a trusted brand like Panasonic Duracell or Energizer. They are typically available in your local hardware store, or online.

After you've changed the battery on the coin cell It is possible to test it by standing close to your fiat punto key fob fiat 500 key fob programming and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switch.

If the fob's remote doesn't function after replacing the battery, it may be damaged by water that blocks it from connecting to the receiver module inside your vehicle. Water damage can happen in many ways, including an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this does not work, you'll have to get your fob reset by an auto locksmith or a dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean or wash it in a washer. Saltwater is particularly dangerous to the fob's circuit board which causes it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an option but if you accidentally drop it in an empty cup of water, or do not remember to take it out of your pants pocket before running the washing machine Don't give up hope.

First, remove the battery. Clean the electronic chip using isopropyl ethanol or a similar product and dry it completely before replacing the battery. Test the fob afterward to see if it is working. If the key does not work, it might need to be reset. This is usually handled by a dealer or professional auto locksmith.

If the key is a newer model and hasn't been programmed to your car it is likely to need to be replaced completely. A professional locksmith for cars can do this job. The locksmith needs to cut the key to match the ignition of your car. They'll also have to program the fob into the system of your car. It's a simple and affordable process that is usually completed within the same day.

Receiver Module Issues

Your 500 key fob might stop working because it is out of range. The remote's range is of 30 feet. So in the event that you are far from your car it will not respond to your commands. You can fix this by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly called a "button" or "watch") and the fob won't work, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob will solve the problem. You can find instructions on how to do this on the majority of vehicles by searching YouTube or consulting the owner's manual.

You may have to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension it could prevent the battery from sitting properly and cause your remote to malfunction.

In rare instances, the fob might be out of sync with your vehicle because of software or hardware problems. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances, the software may also require reinstallation in your body control modules.

Interference

In addition to a dead battery on a coin the key fob could not be able to transmit or receive an signal due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob may not work because of a problem with the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method to reset every single system on board in your 500 keys, including the key fob. Disconnect the battery 12 volt for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will eliminate any residual electricity and restart the car's computers, which can help the key fob to function again. If the issue persists you should seek out an expert technician. They will be able to identify the root cause of your problems.