Reasons Your fiat panda key programming 500 Key Fob Won't Work

A key fob with the fiat doblo key panda key (click the next page) 500 number is a convenient method to open the doors and start the car. However, there are numerous reasons why the fob won't be functioning. These include a dead battery damage to the receiver module, water issues, and interfering.

This listing is for a NEW replacement fiat punto key fob replacement Flip Key Remote - like the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs offer a limited range of operation and must be within just a few inches of the vehicle in order to function. If you are not within your vehicle, and you hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens then replace the battery for your coin-cell (Part Number CR2032) with a new battery from a reputable brand like Panasonic Duracell or Energizer. They are available at the local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your fiat 500x key fob programming 500. The parking lights should flash and the key fob should operate the lock and unlock switches.

If your key fob doesn't work even after replacing the battery, it may be water damage which prevents it from interacting with the module inside your vehicle. Water damage can happen in a variety of ways, ranging from an accidental splash to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If that doesn't work, the fob might need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean, or wash it in a washing machine. Saltwater is particularly dangerous to the fob's circuit board, causing it to short out and eventually end up dying. It's not the best idea to submerge the fob in water, but don't give it up even if you accidentally drop the fob in water or fail to remove it from your pocket.

First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Check the fob again to determine if it's functioning. If the key doesn't work, it might need to be changed. This is usually done by an auto locksmith or dealer.

If the key is older and has not been programmed to your vehicle, it will likely need to be replaced completely. This is a simple process which can be accomplished by a professional automotive locksmith. The locksmith will require the key cut to match the car's ignition. The locksmith will also have to program your fob into the vehicle's system. This is a quick and cost-effective procedure which can be completed within the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob could stop functioning is because it's out of range. The remote typically has an operating range of 30 feet or less, and if it's too far from your car, it will not respond to your commands. It is possible to remedy this by moving your remote closer to your vehicle until it responds.

If your fob isn't working after replacing the battery inside the coin, which is also called a "button", "watch" or "button" it could be due to an issue with the circuit board inside. In most cases, reprogramming the fob will resolve this problem. You can find the steps for most vehicles on YouTube or in the owner's manual.

You may have to replace the metal clips that keep the coin battery in place. If they lose tension they could stop the coin battery from being seated properly and can cause your remote to malfunction.

In rare instances, the fob might be out of sync with your vehicle because of hardware or software problems. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances it may be necessary to install the software again in your body control module as well.

Interference

Interference can also cause the key fob not to receive or transmit signals. This could happen when the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob might not work due to a poor connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery of 12 volts for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers. This can help you get your key fob working again. If the problem persists you should speak with an expert technician. They can identify the exact cause of any issues.