How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners must follow a set of steps that are unique to add an additional ignition key. It requires dealer service with a handheld computer called Tech-2. Then the transponder is replaced and a key need to be purchased.

Rotate your keys to prevent one from wearing out more than the next. This will help to keep your keys in good condition.

Replacement Case

The new key fobs for keys are not like the old saab key replacement keys. They have electronics which make it hard to duplicate. This has made car theft significantly more difficult than it was just a few years ago. It also makes it more costly to replace keys that were lost.

Saab 9-3 owners should have two working keys. If one of them is lost, it costs a fortune to add another to the car, as it requires replacing the CIM module and reprogramming the locking cylinders. Dealers charge between $100 and $200 for this.

There are a few ways to avoid these costly. Certain parts suppliers will utilize the code of an old key to cut a brand new metal blade at a fraction that of a dealer. The key must be exactly the same as the original for it to function in your vehicle.

Follow these steps to replace the case. You will need a flathead screwdriver and some patience. With the screwdriver, pry apart the plastic, and then take off the emergency key. Once the case has been opened take the electronics out and put them in your new case. Be sure to put the correct key and badge back into the case as well.

Replacement Battery

The replacement battery for the saab key fob repair 9-3 is a low-cost part that can be replaced quickly and easily. This YouTube video from Cyclone Cyd shows how to replace the battery of the remote fob with just four easy steps. This tutorial can be used for any modern saab key fob however, the procedure may differ slightly.

The first step is to find the button that opens the backup key in the fob. It is usually located near the saab replacement keys logo on the back of the fob. Use a flathead screwdriver to insert the screwdriver into the tiny hole on this button. This will be enough to allow you to open the case of the fob to allow you to replace the battery.

Once you have installed the batteries CR1632, you can reassemble the remote key fob. Then, you can program it into your car. The entire process should not exceed an hour. It's a simple process that does not require any special equipment.

If you lose your key, the process is somewhat more complex, but it can still be done. The dealer will need to determine the VIN of the car and then purchase a replacement key blade and TWICE module with the exact unique code. The dealer will then need to program the key using MDI which is a new software tool.

Replacement Key Fob

The key fob is the part that locks and unlocks your car, it has a battery inside. The batteries last for a certain time that is a long time, and they eventually die. This is a typical issue that affects all cars and the good thing is that you can change the batteries on most key fobs and not have to replace the entire case. You can purchase fobs replacements on Amazon that come with all the electronics already in place, so you'll simply open the case and replace the batteries in the original case. It's important to note that you will need to remove the emergency key first. you can accomplish this by inserting the small screwdriver flathead into the slot located in the middle of the case. The screwdriver should be moved around the case, and it should split open, making it much easier to remove.

If you're looking to replace your keys, make sure you have a spare on hand. This can save you a lot of money. If you have a spare you can ask the dealer cut an additional key and program it to the car, which is cheaper than replacing the whole key fob.

If you don't have a spare you can add another key to your car, however this will require a lot of research and effort. A second key can cost a few hundred dollars, and it also requires the programming of the car's computer. This can be accomplished by a professional, but it's a costly choice for the majority of owners.

Replacement Ignition

In contrast to the earlier Saab automobiles, the new SAAB 9-3 models use an extremely sophisticated alarm system that is built around a coded key. This means that should you lose only one working key, acquiring another one can be very expensive as the car has to have a special computer module fitted and must also be specifically programmed to accept an extra key. Locksmiths typically aren't able to program this and even dealers can charge several hundreds of dollars just to program the new key!

If you've lost only one working key, a dealer will replace your car's computer (known as the CIM or Saab 9-3 Key Not Accepted Contact Service TWICE) in order to make an exchange, and they will charge you a premium price for it. Instead we can reprogram the EEPROM on your existing car computer to prepare it for a new key, which will save you more than 50% of the price you be charged at a dealership.

If you've been a long-time owner of an 03-11 SAAB 9-3, you probably are aware that the ignition key isn't the most robust. They can become extremely sticky and the buttons can fall off of them at times and you should think about replacing your ignition key if it isn't working properly. It's not as difficult as it seems to replace the ignition key. With the right tools, it is able to be done quickly.