Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the Fiat 500 allows you to easily open doors and start your car. There are many reasons why the fob could stop working. This could be due to a dead battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an NEW replacement fiat remote Key Replacement Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't work is a dead battery. Modern key fobs have a restricted operating range, and should be within only a few feet from the car to operate. If you're not close to your vehicle, and you press the key fob button the car won't respond and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a reputable brand such as Panasonic, Duracell, or Energizer. They can be found in your local hardware store or on the internet.

After you've replaced the coin cell battery you can test it by standing next to your fiat 500 replacement remote key cost 500 and pressing the buttons. The car will blink its parking lights and the key fob should be able to operate the lock and unlock buttons.

If your fob's key does not work after replacing the battery, it may be water damage which is preventing it from connecting to the module inside your vehicle. Water damage can occur in many ways, such as simply splashing or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work, your fob is likely to need to be reprogrammed by a professional auto locksmith or the dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean, or wash it in a machine. Saltwater can cause the circuit board to short and then cease to function. The fob getting wet is not an ideal idea however, if you drop it in an empty cup of water, or don't remember to remove it from your pocket before you run the washing machine do not give up hope.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Check the fob again to determine if it's functioning. If the key doesn't work, it might need to be changed. This is typically handled by a dealer or professional auto locksmith.

If your key is old and not programmed for your vehicle You will need to replace it completely. This is a simple process which can be accomplished by a professional automotive locksmith. The locksmith will require the key cut to match your car's ignition. The locksmith will also need to reprogram your fob in the car's system. This is a cost-effective and quick procedure that can be completed within the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob may stop functioning is that it's out of range. The remote has a maximum range of 30 feet, so if you are too far away from your vehicle it will not respond to your commands. It is possible to solve this issue by moving the remote closer to your vehicle until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob will resolve this issue. You can find instructions on how to get fiat key code to do this for most vehicles by searching YouTube or looking through the owner's manual.

You may need to replace the metal retaining clips that keep the battery of your coin in place. If they become loose, it can stop your coin battery from being properly seated and cause your remote to malfunction.

In rare instances, the fob might be out of the vehicle's sync because due to hardware or software issues. This could be a huge headache, but you can frequently fix this issue by visiting an auto locksmith to reprogram your fob. In certain instances, the software may also require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit a signal. This could happen when the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fob might not function may be a lack of connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while suddenly, or after trying everything you can at home to fix it e.g. You might have a damaged 500 receiver module If you've tried replacing it with a battery, reprogramming or using an alternative key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge and Fiat remote key Replacement restart the car's computer system, which could allow you to get your key fob working again. If the problem persists you should speak with an expert technician. They will be able to determine the root of any problems.