Choosing Upvc Window Replacement Hinges

Selecting and fitting upvc windows replacement hinges isn't as difficult as you may think. Check that the arrows on the hinges are facing the correct direction and measure the thickness of the hinge arms on the opening frame (13mm or17mm).

There are several different types of hinges, each with their own unique features. This article will discuss the most popular types of uPVC window hinges and their advantages.

Egress/Easy Clean Hinge

They are a great choice for replacing or upgrading a fire escape safety window since they open at a full 90-degree angle. They can also be lowered to an 'easy clean' position so that you can easily access the exterior of your windows to clean them without climbing a ladder or lean over at potentially dangerous angles.

Yale is one of the most trusted and well-known brands in the world of home security. These hinges can be used with any type of uPVC side-hung window. They can be moved into the clean position by pressing in a small button and then sliding the window sash over to one side. When the window is closed, the sash will be returned to its original position.

Both 13mm and 17mm sizes are available. Use our Egress Selection Guide to help you determine the best product for your window.

These hinges can be fitted to traditional side-hung frames made from aluminum or uPVC. The friction screw is used to adjust the resistance. This makes opening the windows easier and reduces the chances of closing the window accidentally during severe winds. They have been cycle tested to more than 30,000 cycles and are compliant with BBA/Secured by Design and British Standards approved BS EN 13126-6:2008.

The Nico Egress Easy Clean friction hinge is simple to use and doesn't have any buttons or catches. It is a simple and safe solution to emergency exit and cleaning. Press the hinge retention clip located on the inside of the bottom corner. This will release both the top and bottom catches which will allow you to slide the sash to the clean position. Close the window after you have the sash in the easy-cleaning position. This will reset the hinges to their egress positions.

Fire-Escape Hinge

Fire Escape Hinges, often known as "Easy Clean" hinges are used to replace side-opening windows for escape (fire safety) reasons. They allow for more space in the event of fire. Building regulations stipulate that this type of hinge must be installed in any habitable space with windows.

The windows feature an elongated friction that permits the windows to open up to a 90-degree angle. They also let the opening sash to slide across the glass when it is opened and allows for easy cleaning without the need to climb ladders. The hinges are simple to operate and do not have complicated buttons or catches. They can be operated from inside of the house with an easy, safe lever.

The hinges, which are manufactured in the UK by Cotswold are fitted with a child safety feature for everyday use. It can be reverted by an invisible button. You will have peace of assurance that your children won't accidentally open the windows too far. They are available in 13mm and 17mm stack heights.

Take a measurement of the length of the side-hung window hinge that is attached to the frame. (See the guide for measuring upvc window hinges). Choose the proper size hinge from the list below.

Be aware that the measurement is taken from the component that attaches to the frame not the sash. The actual hinge length may be shorter or longer based on the manufacturer of your old windows. When choosing the size of your hinge, most windows made of upvc will have a 13mm stack height. However, should your window frame have 17mm then choose the option to use this. Alternatively you can fit the 4mm packer to make up the difference. All hinges are in two different directions (1 left and one right). Screws are not included with the hinges. If required, these screws can be purchased separately. Our window repair screws made of upvc are highly recommended. These screws are designed to improve the performance of your hinges and allow them to work smoothly for longer. They have a lower friction design and a better weather seal, with a brand new nylon reducer end cap.

Restricted Hinge

There are occasions when windows must completely open, and this can be a challenge with a standard hinge. The restricted child safety friction hinges can help overcome this issue and provide a solution for situations where ventilation is required but access to clean up or escape in case of fire is not feasible. They work by restricting the amount of sash that can open and allow the override of this restriction with an option. They are available in 13mm and 17mm stack heights. They can be used to open both side and top hung windows.

The Nico Restricted Egress Friction Hinges blend the benefits of a standard restrictor and a pivot for fire escape to provide a simple and efficient method of complying with building regulations. It is suitable for both side hung and top opening uPVC windows and is available in 13mm and 17mm stack heights. It comes in two parts, with one hinge being the one that is restricted for egress, and the other being the unrestricted. This lets one hinge be placed at the bottom, while the other hinge is placed on top.

These uPVC hinges are restrictive and have been tested to BS6375, part 2 and are designed for use on a window that isn't able to be fully opened, like a small children's bedroom. The mechanism limits the extent to which the sash can open to a safety position of 100mm and then re-engages when the window is closed.

These uPVC friction-type hinges can be used with all types of windows. They are especially useful for windows that are hard to reach, like those in three-storey houses or those that require the use of a ladder. They can be combined by our security enhancements such as hinge guards and protection plates, or dog bolts for PAS 24 performance.

It is crucial to take measurements of the hinge on your current window to ensure that you get replacements that are the same size. The easiest method to accomplish this is by looking at the hinge in the image gallery and determining the best place for it to be. The top-hung hinges can only be positioned on one side, while the side hung ones can only be positioned on one side.

Standard Hinge

A standard hinge has metal-to-metal contact, and there are no additional components to reduce friction. It's available in a range of finishes and is also fire-rated. To determine the radius of your hinge put it on its flat surface and line up a dime and quarter in two corners. If the dime is more snug and the corner is round by 1/4 inch; if the quarter fit better, it's rounded by 5/8 inch.

The right hinge can make or ruin the appearance of your door hinge repair. It's crucial to match the finish and style of your composite door hinges to the hinges to create a unified design that is both functional and visually appealing.